Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Understanding Essential Plumbing Skills is Essential for Bathtub Installation
Blog Article
Listed here below you can discover lots of amazing advice pertaining to Tools You Need to Install a New Bathtub .
Setting up a tub isn't specifically brain surgery, however it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is also a reasonably hard task. If the old tub is conveniently accessible, the project can move rapidly; if you have to open up a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly assist you mount a brand-new bath tub in your restroom if you have actually currently purchased a new bathtub as well as do not need to transform the arrangement of your previous water pipelines.
Your devices and also material checklist should make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather troublesome because of the limited gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in place between the tap as well as the sink. Safeguard the tap in position with the maker offered backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
Turn on the water supply as well as inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of at the very least once as this will certainly settle it into its final setting.
Preparing for the Installation
To start with, the supporting frame provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealer can split relatively very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very intrigued by Installing A Bathtub and I really hope you enjoyed reading the page. If you enjoyed reading our blog post please be sure to pass it around. I praise you for your time. Kindly stop by our website back soon.
Immediate help? Ring! Report this page